What it means
C-20 on a Dacor oven means the oven sensor is open or short while the oven operates. Press OFF and restart. If it persists, cut all power for at least 30 seconds and reconnect, and book a technician if the code reappears.
Dacor oven C-20 / Oven sensor
C-20 on a Dacor oven means the oven sensor is open or short while the oven operates. Press OFF and restart. If it persists, cut all power for at least 30 seconds and reconnect, and book a technician if the code reappears.
Also shown as C-20
C-20 on a Dacor oven means the oven sensor is open or short while the oven operates. Press OFF and restart. If it persists, cut all power for at least 30 seconds and reconnect, and book a technician if the code reappears.
Turn the oven off at the controls and start it again to see whether the code clears.
C-20 reappears after a restart and a power cut of at least 30 seconds.
Your Dacor tick-list / held on this device

Turn the oven off at the controls and start it again to see whether the code clears. On the Transitional ranges, turn the mode and temperature knobs to Off first.

If C-20 persists, disconnect all power to the oven for at least 30 seconds (breaker off), then restore power.

An oven sensor that is open or short cannot control the temperature, so do not keep baking with C-20 showing.

The sensor is inside the cavity wall. Tell us C-20 and the model.
Tell us the model and which checks you have done, then open your request from here.
Book a visit
This drawing is schematic, since the inside of a Dacor changes from model to model. Press an outlined part for its photo and the check that goes with it.
The oven temperature sensor circuit is open or short while the oven operates. The Modernist wall oven and Transitional guides print the open and short rows separately under the same C-20 label.
Read the supporting manualPress OFF and restart the oven. If the code persists, disconnect all power for at least 30 seconds, reconnect, and if it still persists, call for service.
Read the supporting manualC-20 is the oven sensor. C-23 is the temperature probe sensor. C-30 is the PCB sensor. They share steps but name different sensors.
Read the supporting manualManufacturer document
Dacor (Dacor-branded document hosted on image-us.samsung.com)
Part No. 112177 Rev B / DG68-00920A-00 / p.64 (two rows: open / short)
Manufacturer document
Dacor (Dacor-branded document hosted on image-us.samsung.com)
DG68-01458A-00, 2023-01-17 (EN+ES+FR) / p.102 (two rows)
Manufacturer document
Dacor (Dacor-branded document hosted on image-us.samsung.com)
DG68-01105E-00, 2020-07-06 (EN+ES+FR) / p.54 (two rows)
Manufacturer document
Dacor (Dacor-branded document hosted on image-us.samsung.com)
Part No. 115113 Rev A / p.71 (either open or short)
The wall oven and Transitional guides print two rows under one C-20 label, open and short. The Modernist 48/36-inch range prints one row, either open or short.
No. C-21 is the abnormally high internal temperature code. C-20 concerns the sensor circuit, open or short.
The guides say to disconnect all power for at least 30 seconds. At a built-in oven that means the breaker.
A bad sensor may bake wrong. Do not rely on the oven until it has been checked.
When C-20 reappears after the restart and a power cut of at least 30 seconds.
Dacor codes, symptoms, parts, repairs
C-23 on a Dacor Modernist wall oven, Transitional range or Modernist 48-inch range means the temperature probe sensor is short while the oven operates. Turn the oven off and restart it. If it returns, cut power for half a minute or longer, then book a technician.
The Heritage wall oven manual lists three owner causes for an oven that will not heat: a wrong temperature setting, a delayed start left on, and a meat probe still plugged in when you broil. Check those in that order, then look at the display for a C- code.
Book a diagnostic for your model at the appliance itself.
Office details and the access notes to pass on.