Dacor oven C-22 / Control board sensor

Dacor oven
error C-22

Oven / display referenceC-22

C-22 on a Dacor Transitional range means the Sub PCB sensor is open or short while the oven operates. Turn both knobs to Off, restart, cut power for at least 30 seconds if it persists, then book a technician.

Also shown as C-22

Last reviewed

Oven / display referenceC-22
Meaning
C-22 on a Dacor Transitional range means the Sub PCB sensor is open or short while the oven operates. Turn both knobs to Off, restart, cut power for at least 30 seconds if it persists, then book a technician.
Who handles it
Reset, then book
Related codes
Source
User Manual, Gas Pro Range DOP30*840**

What Dacor oven C-22 means.

What it means

C-22 on a Dacor Transitional range means the Sub PCB sensor is open or short while the oven operates. Turn both knobs to Off, restart, cut power for at least 30 seconds if it persists, then book a technician.

What you can safely check

Set the mode and temperature selector knobs to Off, as the Transitional guides print.

When to call a technician

C-22 returns after a restart and a power cut of at least 30 seconds.

Your Dacor tick-list / held on this device

Safe checks, in order.

0 of 4 checks done
  1. Dacor oven C-22: Ranges & ovens in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Turn both knobs to Off

    Set the mode and temperature selector knobs to Off, as the Transitional guides print.

  2. The control panel of a Modernist wall oven
    Illustration. Follow your model’s instructions.
    Check 2

    Restart the oven

    Start it again and see whether C-22 returns.

  3. Over-the-shoulder view of a technician holding a tablet with a blank checklist, a stainless dishwasher behind.
    Illustration. Follow your model’s instructions.
    Check 3

    Disconnect power

    If it persists, disconnect all power to the oven for at least 30 seconds, then reconnect.

  4. A technician testing a wall oven component
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    If the code remains, the sub board sensor needs a technician.

Still showing C-22?

Tell us the model and which checks you have done, then open your request from here.

Book a visit

The oven temperature sensor.

Conceptual Range / oven sectionTemperature sensorWiringControl123
  1. 1Temperature sensor
  2. 2Wiring

This drawing is schematic, since the inside of a Dacor changes from model to model. Press an outlined part for its photo and the check that goes with it.

A little more context.

What does C-22 mean?

The sensor on the Sub PCB, a secondary circuit board, is open or short while the oven operates.

Read the supporting manual

How is it different from C-30?

C-30 is the sensor on the main PCB. C-22 is the one on the Sub PCB. Both use similar reset steps.

Read the supporting manual

Can I keep using the oven?

The guides give no workaround. Do not rely on the oven until it has been checked.

Read the supporting manual

The manual behind the message.

Manufacturer document

User Manual, Gas Pro Range DOP30*840**

Dacor (Dacor-branded document hosted on image-us.samsung.com)

DG68-01458A-00, 2023-01-17 (EN+ES+FR) / p.102 (two rows)

Manufacturer document

User Manual, Dual Fuel Pro Range DOP36P86DL*

Dacor (Dacor-branded document hosted on image-us.samsung.com)

DG68-01105E-00, 2020-07-06 (EN+ES+FR) / p.55 (two rows)

Printed only in the Transitional 30-inch DOP30*840** and 36-inch DOP36P86DL* guides. Not in the Modernist wall oven or 48-inch range tables. The 30-inch has its own solution cell; the 36-inch shares the C-21 cell.

Here to help

Good questions.
Clear answers.

Talk to our team
Why does this guide mention knobs?

Transitional ranges use mode and temperature knobs. Turning both to Off is how you stop the oven before restarting.

Is C-22 on the Modernist wall oven?

No. The Modernist wall oven table does not list C-22. It is printed only in the Transitional 30-inch and 36-inch range guides.

Is C-22 the same as C-F0?

No. C-F0 is a lost connection between the main and sub boards. C-22 is a sensor on the Sub PCB.

What do I tell the technician when C-22 shows?

The code, the model and whether it returned after the 30-second power cut.

Let’s take care of it.

See a C-code?
Tell us the number.