Dacor dishwasher 4C / Water supply

Dacor dishwasher
error 4C

Dishwasher / display reference4C

Not enough water is reaching the dishwasher when the DDW24G9000AP shows 4C. Check whether the supply valve is closed or the supply is suspended, and whether the inlet valve or line is frozen or clogged. If it persists, a technician visit is next.

Also shown as 4C

Last reviewed

Dishwasher / display reference4C
Meaning
Not enough water is reaching the dishwasher when the DDW24G9000AP shows 4C. Check whether the supply valve is closed or the supply is suspended, and whether the inlet valve or line is frozen or clogged. If it persists, a technician visit is next.
Who handles it
Owner checks first, then a technician
Related codes
Source
User Manual, Built-In Dishwasher DDW24G9000AP

What Dacor dishwasher 4C means.

What it means

Not enough water is reaching the dishwasher when the DDW24G9000AP shows 4C. Check whether the supply valve is closed or the supply is suspended, and whether the inlet valve or line is frozen or clogged. If it persists, a technician visit is next.

What you can safely check

Check that the water supply valve under the sink is fully open.

When to call a technician

4C continues after the valve is open and the supply is on.

Your Dacor tick-list / held on this device

Safe checks, in order.

0 of 4 checks done
  1. Dacor dishwasher 4C: Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Open the supply valve

    Check that the water supply valve under the sink is fully open.

  2. The control panel of a Modernist wall oven
    Illustration. Follow your model’s instructions.
    Check 2

    Check the household supply

    The manual lists a suspended supply. Run a nearby tap to confirm water is flowing.

  3. Over-the-shoulder view of a technician holding a tablet with a blank checklist, a stainless dishwasher behind.
    Illustration. Follow your model’s instructions.
    Check 3

    Think about freezing

    A frozen inlet valve or line is a printed cause. Check for a cold cabinet or an unheated space.

  4. A technician testing a wall oven component
    Illustration. Follow your model’s instructions.
    Check 4

    Look for foreign particles

    A clogged inlet valve or line is also listed. If you cannot reach it safely, leave it to a technician.

Still showing 4C?

Tell us the model and which checks you have done, then open your request from here.

Book a visit

Where a leak is caught.

Conceptual dishwasher sectionTub seam / gasketBase panFloat switchInlet valve1234
  1. 1Tub seam / gasket
  2. 2Base pan
  3. 3Float switch

This drawing is schematic, since the inside of a Dacor changes from model to model. Press an outlined part for its photo and the check that goes with it.

Parts behind the message.

Braided stainless dishwasher supply hose and a brass elbow fitting on a towel in front of a built-in dishwasher

Component reference

Dishwasher water inlet valve

Hot water enters the Dacor DDW24G9000AP through its dishwasher water inlet valve, fed by a 3/4-inch 90-degree fitting.

Read the definition

A little more context.

How do I tell a house supply problem?

If other taps are dry or weak, the supply is the issue. If they run normally, the problem is between the valve and the dishwasher.

Read the supporting manual

Is 4C the same as 1C?

No. 1C is a low-water level check within the cycle, with filter and loading advice. 4C is about water arriving at all.

Read the supporting manual

The manual behind the message.

Manufacturer document

User Manual, Built-In Dishwasher DDW24G9000AP

Dacor (Dacor-branded document hosted on image-us.samsung.com)

DD68-00250L-00 (DW8700B), 2024-01-11 / PDF p.74

For 4C: the Dacor built-in dishwasher DDW24G9000AP. Source is the information codes table and the dishwasher troubleshooting and installation chapters of its user manual; other Dacor dishwashers are not covered.

Here to help

Good questions.
Clear answers.

Talk to our team
Could cold weather cause 4C?

Yes. The manual names a frozen inlet valve or line as one cause, so check for an unheated or very cold space around the supply.

Should I run the dishwasher again?

Only after you have opened the valve and checked the supply. Repeated attempts do not help.

Can I clean the inlet valve myself?

The manual does not describe it. Leave the inlet valve and line to a technician.

When do I book when 4C shows?

When 4C continues after the valve is open and the supply is on.

Let’s take care of it.

See a C-code?
Tell us the number.