Before work starts
The technician describes the repair and agrees the cost with you before starting. We confirm the final figure once the oven, range or cooktop has been inspected.
Independent appliance repair
We repair the Dacor 24-inch built-in dishwasher when it will not start, leaves water behind, cleans poorly, smells or shows LC or 9C9. Those two codes need action first: shut the water and breaker for LC, unplug for 9C9. Then book a technician.


On a Dacor DDW24G9000AP, the manual lists a door not fully latched, the upper rack not joined to its duct nozzle, Start (Reset) not pressed, no cycle chosen, an unplugged cord, and a closed water valve. Run those six checks before calling.

For standing water in a Dacor DDW24G9000AP, the manual points to a folded or clogged drain hose and a clogged drain system, and says to clean the drain pump by removing its cover. A 5C code points to the same places.

The DDW24G9000AP manual covers leaks in its install steps, not its troubleshooting table: check both ends of the water line and the drain connector, and wipe the water leakage sensor. An LC code means shut the water valve and turn off the breaker.

The DDW24G9000AP manual blames clogged filters or nozzles, the wrong cycle, too little detergent, low water pressure or temperature, overloading, hard water, and an unbalanced upper rack. Start with the filters and a cycle that suits the soil.
Leakage check is the meaning of LC on this Dacor dishwasher, the DDW24G9000AP. Shut the water supply valve and set the dishwasher breaker to off. Do not run it again until the leak is dealt with; the manual refers the repair to the installer.
Overheating of the IPM is reported as 9C9 by the DDW24G9000AP. The manual prints one action: unplug the appliance. The dishwasher is built in, so switch its breaker off if you cannot reach the plug, then book a visit.
Part names come once the technician has run the diagnostic and read your model and serial number. We order nothing on a hunch, and you approve the cost before any work starts.

The Dacor DDW24G9000AP has a coarse filter and a cylindrical micro filter under it, locked by a handle in the tub floor. The manual says to clean them every month. Food left on dishes, or a weak clean, points here first.

The drain hose is the exit path for used wash water. The Dacor manual lists a folded or clogged hose when water remains after a cycle, and an obstructed hose for bad odors. It sends obstruction removal to a technician. An LC reading means shutting the water and the breaker off.
How the visit goes.
Clear steps, start to finish.

Choose the appliance and share the code or symptom. Mention whether yours is a Modernist or a Transitional model.

The technician traces the issue, explains it in plain terms and agrees the cost with you before any repair begins.

Once the repair is done, the technician checks the result with you and explains what was replaced.
Make sure the door is latched and a cycle is chosen, then press Start. A power cord not connected also stops it.
Food left on dishes can come from clogged or loose filters or nozzles. See the filter page for the steps.
The valve must be open, and the manual wants hot supply, ideally reaching 120 F, with pressure between 20 and 120 psi.
Water left after a cycle can come from a folded or clogged drain hose.
LC: close the supply valve and switch the dishwasher breaker off. 9C9: unplug the dishwasher. Leave both for the technician.
Schedule a visit when LC or 9C9 appears, after you have shut the water or unplugged the unit.
Schedule a visit when water remains with the filters and hose clear.
Schedule a visit when dishes stay dirty with clean filters, hot water and the right cycle.
Shut off the water and power at once if anything leaks.
Arrange a diagnosticThe technician describes the repair and agrees the cost with you before starting. We confirm the final figure once the oven, range or cooktop has been inspected.
Dacor handles repairs that its manufacturer warranty covers. We provide a warranty of our own on the work we do.
The DDW24G9000AP manual prints it as a leakage check. Close the water supply valve and switch the dishwasher breaker off. It then points you to repair.
The manual says the IPM is overheating, and the only step is to unplug the dishwasher. Do not run it again until a technician has looked.
No. In this manual F0 to F6 are rinse-aid levels, and F4 is the default setting rather than an error.
The code table we read is for the DDW24G9000AP only. Older models may differ, so give us your model number when you book.
While the manufacturer's warranty runs, that repair is the manufacturer's to handle. Once it ends, or if you prefer an independent technician, book a visit and the cost is settled with you first.
Dacor codes, symptoms, parts, repairs
Leakage check is the meaning of LC on this Dacor dishwasher, the DDW24G9000AP. Shut the water supply valve and set the dishwasher breaker to off. Do not run it again until the leak is dealt with; the manual refers the repair to the installer.
On a Dacor DDW24G9000AP, the manual lists a door not fully latched, the upper rack not joined to its duct nozzle, Start (Reset) not pressed, no cycle chosen, an unplugged cord, and a closed water valve. Run those six checks before calling.
The Dacor DDW24G9000AP has a coarse filter and a cylindrical micro filter under it, locked by a handle in the tub floor. The manual says to clean them every month. Food left on dishes, or a weak clean, points here first.
Book a diagnostic for your model at the appliance itself.
Office details and the access notes to pass on.