Read the whole display
Read the exact characters on the display, such as 9C9 or 4C, and give the model number from the door edge or the manual cover.
Model-specific code library
We decode LC, 4C, 5C, HC, 3C, 1C, 9C9 and the AP pairing prompt, all from the DDW24G9000AP manual. LC and 9C9 get their own pages because they ask you to cut water or power.
Leakage check is the meaning of LC on this Dacor dishwasher, the DDW24G9000AP. Shut the water supply valve and set the dishwasher breaker to off. Do not run it again until the leak is dealt with; the manual refers the repair to the installer.
Read the LC checks8 researched dishwasher codes. A display message can mean something different on each model, so the manual for yours has the last word.
The low-water level check is what 1C stands for on the DDW24G9000AP. Check whether the filter is clogged, use dishwasher detergent, load dishes evenly, then turn the dishwasher off and on and try again. A technician visit is next if it continues.
Owner checks firstPump operation check is the printed meaning of 3C for the Dacor DDW24G9000AP. Turn the dishwasher off and restart it. If the issue continues, book a visit; the manual lists no other owner step.
Reset, then bookNot enough water is reaching the dishwasher when the DDW24G9000AP shows 4C. Check whether the supply valve is closed or the supply is suspended, and whether the inlet valve or line is frozen or clogged. If it persists, a technician visit is next.
Owner checks firstA drain problem is what the DDW24G9000AP reports with 5C. Shut the water supply valve, then check whether the drain hose is clogged or folded and whether the drain hole inside the pump is clogged. A technician visit is next if it continues.
Owner checks firstOverheating of the IPM is reported as 9C9 by the DDW24G9000AP. The manual prints one action: unplug the appliance. The dishwasher is built in, so switch its breaker off if you cannot reach the plug, then book a visit.
TechnicianAP is no error on the DDW24G9000AP; it is a pairing prompt. Press and hold Smart Control on the control panel to connect the dishwasher with your smartphone. Ignore it if you do not use the app.
Information onlyThe DDW24G9000AP uses HC for a high temperature heating check. With the dishwasher empty, add detergent and run a cycle. If it persists, switch the dishwasher breaker off and book a visit.
Reset, then bookLeakage check is the meaning of LC on this Dacor dishwasher, the DDW24G9000AP. Shut the water supply valve and set the dishwasher breaker to off. Do not run it again until the leak is dealt with; the manual refers the repair to the installer.
Close water / technicianEarlier Dacor dishwashers are not covered. CF, CL, F1, F3, F4, F9, LO, PF, 01-04 and the three-beep pattern are not printed in any Dacor document we read. F4 is a rinse-aid level in the DDW24G9000AP manual, not an error.

We decode LC, 4C, 5C, HC, 3C, 1C, 9C9 and the AP pairing prompt, all from the DDW24G9000AP manual. LC and 9C9 get their own pages because they ask you to cut water or power.
Earlier Dacor dishwashers are not covered. CF, CL, F1, F3, F4, F9, LO, PF, 01-04 and the three-beep pattern are not printed in any Dacor document we read. F4 is a rinse-aid level in the DDW24G9000AP manual, not an error.
Read the exact characters on the display, such as 9C9 or 4C, and give the model number from the door edge or the manual cover.
Close the water supply valve and switch the dishwasher breaker off if water is on the floor or the display shows LC or 9C9. Do not run the dishwasher again until it has been checked.
On a Dacor DDW24G9000AP, the manual lists a door not fully latched, the upper rack not joined to its duct nozzle, Start (Reset) not pressed, no cycle chosen, an unplugged cord, and a closed water valve. Run those six checks before calling.
For standing water in a Dacor DDW24G9000AP, the manual points to a folded or clogged drain hose and a clogged drain system, and says to clean the drain pump by removing its cover. A 5C code points to the same places.
The DDW24G9000AP manual covers leaks in its install steps, not its troubleshooting table: check both ends of the water line and the drain connector, and wipe the water leakage sensor. An LC code means shut the water valve and turn off the breaker.
Rely on the guide for your precise model. Look at how we research these pages.
Earlier Dacor dishwashers are not covered. CF, CL, F1, F3, F4, F9, LO, PF, 01-04 and the three-beep pattern are not printed in any Dacor document we read. F4 is a rinse-aid level in the DDW24G9000AP manual, not an error.
Take a photo of the entire dishwasher panel and one of the rating label. Write down what the appliance was doing when the message came up, and never lean on another product's explanation.
An old search phrase counts for nothing next to the manufacturer's own words. If a dishwasher document gives no decoding, the message appears under its name with no part or cause guessed at.
Open any manufacturer document in this dishwasher library, then match the model on its cover to the label on your appliance. A different model has its own guide.