Dacor cooktop F1 / Communication

Dacor cooktop
error F1

Cooktop / display reference

F1 is how the Modernist induction cooktop reports that communication with the EEPROM failed. Restart with the POWER button, then disconnect power for more than 30 seconds if it continues. Book a visit if it stays.

Also shown as F1

Last reviewed

Cooktop / display reference
Meaning
F1 is how the Modernist induction cooktop reports that communication with the EEPROM failed. Restart with the POWER button, then disconnect power for more than 30 seconds if it continues. Book a visit if it stays.
Who handles it
Reset, then book
Related codes
Source
User Manual, Electric Cooktop DTI36M977BB / DTI30M977BB

What Dacor cooktop F1 means.

What it means

F1 is how the Modernist induction cooktop reports that communication with the EEPROM failed. Restart with the POWER button, then disconnect power for more than 30 seconds if it continues. Book a visit if it stays.

What you can safely check

Press the POWER button to restart the cooktop.

When to call a technician

F1 stays after a POWER restart and a power reset of more than 30 seconds.

Your Dacor tick-list / held on this device

Safe checks, in order.

0 of 4 checks done
  1. Dacor cooktop F1: Induction cooktop propped up for service with its plug pulled, a gloved hand pointing at the ribbon cable connector on the green control board
    Illustration. Follow your model’s instructions.
    Before you begin

    Restart with POWER

    Press the POWER button to restart the cooktop.

  2. Cooktops in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Cut power for more than 30 seconds

    If F1 continues, disconnect power for over 30 seconds and then restart.

  3. The control panel of a Modernist wall oven
    Illustration. Follow your model’s instructions.
    Check 3

    Do not keep retrying

    Several restarts in a row will not change a memory chip communication problem.

  4. Over-the-shoulder view of a technician holding a tablet with a blank checklist, a stainless dishwasher behind.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    The EEPROM sits on the control board, which only a technician should work on.

Still showing F1?

Tell us the model and which checks you have done, then open your request from here.

Book a visit

Cooktop control.

Conceptual Cooktop sectionTouch panelUser interface boardPower boardWiring1234
  1. 4Wiring

This drawing is schematic, since the inside of a Dacor changes from model to model. Press an outlined part for its photo and the check that goes with it.

Parts behind the message.

Bare green circuit board with a square chip, a capacitor and white connectors lying on a dark gray mat on a kitchen counter.

Component reference

Induction cooktop main and sub boards

The cooktop main and sub boards are two circuit boards that work together inside the Modernist induction cooktop, with an EEPROM memory chip alongside.

Read the definition

A little more context.

What does F1 mean?

The cooktop could not communicate with its EEPROM, a small memory chip that holds settings.

Read the supporting manual

How is F1 different from F0?

F0 is the link between the main and sub boards. F1 is the link to the EEPROM. Both share the same restart and power reset remedy.

Read the supporting manual

The manual behind the message.

Manufacturer document

User Manual, Electric Cooktop DTI36M977BB / DTI30M977BB

Dacor (Dacor-branded document hosted on image-us.samsung.com)

Part No. 113935 Rev. A / DG68-00899A-00 (2017-03-16) / PDF p.63 (Information codes)

For F1: the Modernist induction cooktops (DTI30 and DTI36 series). Source is the Information codes table in the troubleshooting chapter of their user manual; other Dacor cooktops are not covered.

Here to help

Good questions.
Clear answers.

Talk to our team
What is an EEPROM?

A memory chip on the control board. The manual names it in the code table without explaining it.

Can I fix F1 by replacing the cord?

The manual gives no such step. The only owner steps are a POWER restart and a power reset of more than 30 seconds.

Is it connected to the Wi-Fi function?

The manual does not link F1 to the Wi-Fi function. It ties F1 only to communication with the EEPROM memory chip.

When do I book when F1 shows?

When F1 comes back after a restart and a power reset of more than 30 seconds.

Let’s take care of it.

See a C-code?
Tell us the number.