Error codes explained

Shutting off a Dacor dishwasher before a service visit

To shut off a Dacor DDW24G9000AP dishwasher for service, hold Start for three seconds to drain, shut the water supply valve, then switch the dishwasher off at its breaker or unplug it. The manual prints these in its leak steps and code table, not as one list. Keep it off until the visit. [1]

An open sink cabinet showing a shutoff valve and braided hose to the dishwasher, a folded towel and phone on the floor.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Holding Start for three seconds cancels the cycle and drains the tub. 1
  • LC: close the supply valve, then set the dishwasher breaker to off. 1
  • 9C9: unplug the appliance. 1
  • Restore in this order: breaker on, valve open, plug in, then run a cycle and check for leaks. 1
  • This guide covers the January 2024 manual for the DDW24G9000AP only. 1

How do I shut off a Dacor dishwasher before a service visit?#

Drain the tub, shut the water supply valve, then cut the power. The manual does not print one combined sequence, but its leak steps and its code table add up to this order: drain with Start, close the valve, breaker off or unplug. 1

This guide covers the Dacor 24-inch built-in dishwasher DDW24G9000AP, from the January 2024 manual. Earlier Dacor dishwashers may differ, and we have not used their documents here. 1

A small quarter-turn shut-off valve on a copper pipe under a sink, with a braided flexible supply hose attached.
The water supply valve is the first shut-off the manual names. 1

Which step comes first, the valve or the breaker?#

For a leak, the code table puts the valve first: shut the water supply valve, then set the dishwasher's breaker switch to off. The leak steps in the installation chapter drain the tub first, then unplug it, then close the valve. 1

Two lists, two sources of order. With water on the floor, shutting the valve stops more of it arriving. If you can drain the tub first, the installation chapter shows how.

SituationWhat the manual saysWhere
LC on the displayClose the supply valve; set the dishwasher's breaker to offp.74
Final check or leak during installHold Start over 3 seconds to drain; unplug; close the valvep.32
5C on the displayClose the supply valve; look at the hose and the pump drain holep.74
HC on the displayRun an empty cycle with detergent first; if HC persists, breaker offp.74
9C9 on the displayUnplug the appliancep.75
Unused for a long timeDrain fully, disconnect the water hose, shut the valve and the breakerp.68

Your own display tells you which row you are in. The LC page and the 9C9 page explain those two codes in full.

How do I drain the tub with the Start button?#

Hold Start for three seconds. The manual calls this Cancel and Drain, and it stops a running cycle and pumps out the water. In the LC leak steps, the instruction is to hold Start for more than 3 seconds, and to unplug once draining ends. 1

After the reset, the dishwasher takes a new cycle choice and a new press of Start if you want to run it again. 1 For a service visit, you only need the water out, so stop there.

  1. 1

    Hold Start for three seconds#

    This cancels the running cycle and drains the tub. 1

    A fingertip pressing one of four square keys on the control strip of a stainless dishwasher door.
  2. 2

    Wait for the draining to finish#

    In the LC steps the manual says to unplug only when the draining is complete. 1

  3. 3

    Close the water supply valve#

    Turn the valve under the sink to the closed position. The LC and 5C rows both name this. 1

  4. 4

    Cut the power#

    Set the dishwasher's breaker to off at the panel, or unplug the appliance. 1

    An open gray breaker panel with two columns of black switches, one switch on the right side flipped to the opposite position.
  5. 5

    Leave it that way until the visit#

    Do not restart the machine to see whether the code returns. For LC the manual refers the repair to the installer. 1

What should I wipe or clear before the visit?#

Mop up standing water, empty the tub of dishes, and wipe the inside of the tub and door with a wet cloth. The cleaning chapter asks you to leave the long front seal in place and not to spray water onto the machine. 1

If you are comfortable with it, check the filters too. The manual recommends cleaning them every month: turn the handle counterclockwise, take out the Coarse filter and the micro filter beneath it, and rinse both in the sink under running water, then dry them. 1 Our filter and spray arm guide gives the whole order.

One step in the manual we suggest you leave to the visit: after a leak, it shows the dishwasher laid down so that moisture can be wiped from the water leakage sensor. 1 That needs the unit pulled from its cabinet.

A dishwasher laid on its back on a moving blanket, a hand wiping a small sensor on the base pan near hoses and wiring.
The leakage sensor wipe-down is shown with the unit laid down. 1

What does the manual say about restoring everything?#

In the final-check steps of installation, the restore order is breaker on, water valve open, plug in, then run a cycle and check both ends of the water line and the drain hose connector for leaks. 1

Do this only after the cause of a leak or code has been dealt with. If LC appears again after the wipe-down and a restart, the manual says to contact a service center, and that is when to book with us. 1

Is the shut-off different if the dishwasher will sit unused?#

Yes, it goes further. For a long stretch without use the manual calls for emptying the unit fully, taking off the water hose, and shutting off both the water supply valve and the circuit breaker. Water left standing in the hoses or inside parts can harm the dishwasher. 1

That is the only place where the hose comes off. The manual does not ask for it in the leak steps or the code table, so for a short wait before a visit the valve and the power are enough. A dishwasher left standing with dishes in it can also develop a smell; our guide to smells and standing water covers the manual's fixes for that.

What do I need to hand when I book?#

The exact code, what the display and the floor looked like, which shut-offs you used and when, and the model on the manual's cover, DDW24G9000AP. A photo of the display before you cut the power is useful for the visit.

  • The code as shown: LC, 5C, HC, 3C, 1C, 4C or 9C9. If it is AP, that is a pairing prompt, not a failure. 1
  • Whether water reached the floor, and where it seemed to come from.
  • Whether the machine drained when you held Start.
  • Whether a new hose or sink fitting went in recently. The leak steps mention checking the inlet valve connection to the hot water line. 1
  • The install date, when you know it.

The dishwasher service page shows the work we take on, and the leaking dishwasher page has the checks for where the water comes from. The dishwasher code library has a row for every display code in the manual.

Sources#

  1. User Manual, Built-In Dishwasher DDW24G9000APDacor (Dacor-branded document hosted on image-us.samsung.com) · DD68-00250L-00 (DW8700B), 2024-01-11 · PDF p.32-33 (Final check, To fix leaks), p.55 (Start, Cancel & Drain), p.64-68 (Maintenance, Long-term care), p.74-75 (Information codes)

Here to help

Good questions.
Clear answers.

Talk to our team
How do I shut off a Dacor dishwasher?

Hold Start for three seconds to cancel and drain, shut the water supply valve, then switch the dishwasher breaker off or unplug the unit. The manual prints these in its leak steps and its code table, not as one list. [1]

Do I close the water valve or switch off the breaker first?

For LC the manual names the valve first, then the breaker. In its installation leak steps it drains, unplugs and then closes the valve. With water on the floor, close the valve first and keep dry hands for the breaker. [1]

What does the manual say to do for 9C9?

9C9 is listed as the IPM overheating, and the action is to unplug the appliance. It does not list any home checks for that code, so unplug it and arrange a visit. [1]

Can I wipe the leak sensor myself?

The manual shows the dishwasher laid down so moisture can be wiped from the water leakage sensor. That needs the unit out of its cabinet, so we suggest leaving it to the visit. [1]

How do I turn it back on afterwards?

The installation final check gives the order: breaker on, water valve open, plug in, then run a cycle and look for leaks at both ends of the water line and the drain hose connector. [1]

Let’s take care of it.

See a C-code?
Tell us the number.