Independent appliance repair

Dacor range repair, with care.

We repair Dacor freestanding ranges, rangetops and stoves, including Heritage Pro, Transitional and Modernist 48-inch models: burners that will not light, ovens that will not heat, steam problems or codes. Book a technician with the model on hand.

A freestanding stainless gas range with five knobs, a wide oven window and a hood in a warm wood kitchen.
Independent service. Considered care.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
Wall ovensRangesCooktopsRefrigeratorsFreezersDishwashersWine cellarsBeverage centersIce makersHoodsMicrowavesError code helpWarranty on our workmanship

Parts selected after a diagnostic.

Part names come once the technician has run the diagnostic and read your model and serial number. We order nothing on a hunch, and you approve the cost before any work starts.

Part

Range surface burner

A Dacor Pro range burner is a head, a cap and an igniter electrode on a fixed base. The Heritage Pro manual blames a missing cap, a misaligned base or dirty electrodes when a burner refuses to light. Gas smell is a different case: leave the building, then call the gas supplier from outside.

Part

Oven touch control panel

The touch panel on a Dacor oven is where wet or dirty keys cause trouble. The Modernist table prints C-d0 when a control key reads as held for a minute. Wiping the buttons dry and switching the oven off usually comes first. The Heritage manual adds a 6-second CANCEL/SECURE touch to wake a locked panel.

Part

Oven convection and cooling fans

Dacor ovens run a convection fan that cycles on and off while cooking, and a cooling fan that keeps going after the oven is switched off. Both are listed as normal. A real cooling-motor problem shows as C-A2, and the table sends you to service.

Part

Steam oven water reservoir

Dacor steam ranges draw water from a removable reservoir that you fill with tap water before steam cooking. The 48-inch holds up to 1500 ml and the 36-inch up to 650 ml. Empty it afterward so leftover water does not affect other modes. Steam sensor and drain problems print as C-70 and C-72.

Part

Oven temperature probe

The temperature probe is the plug-in wire that reads the food's internal temperature. Dacor Modernist and Transitional tables print C-23 as a short temp probe sensor while the oven runs. A wet or still-connected probe also stops broil, self-clean and Sabbath modes on the Heritage wall oven.

Send the code.
Get a plan.

How the visit goes.
Clear steps, start to finish.

  1. A technician approaching a home entrance with equipment
    1

    Send what you see

    Choose the appliance and share the code or symptom. Mention whether yours is a Modernist or a Transitional model.

  2. A technician testing a wall oven component
    2

    Trace the cause

    The technician traces the issue, explains it in plain terms and agrees the cost with you before any repair begins.

  3. A wall oven running with its display lit
    3

    Confirm the fix

    Once the repair is done, the technician checks the result with you and explains what was replaced.

Prepare for the range visit.

  1. 1

    Smell gas? Leave first

    The Heritage Pro manual says to evacuate and call the gas supplier from a neighbor's home. Do not troubleshoot a gas smell.

  2. 2

    Seat the burner parts

    A burner that will not light may have a missing cap or a misaligned base. Clean the electrodes with a dry cloth.

  3. 3

    Check the knob

    If a burner clicks while cooking, turn the knob from ignite to the setting. If it keeps clicking, it needs service.

  4. 4

    Read the display

    Transitional and Modernist ranges print C-codes. Press OFF, restart, and disconnect power for at least 30 seconds if the code stays.

  5. 5

    Empty the steam reservoir

    On a steam range, empty the water reservoir after steam cooking so it does not affect other modes.

Leave internal testing to a technician.

Schedule a visit when no flame appears although the cap is seated and the electrode is clean.

Schedule a visit when C-23 comes back after power has been cut for 30 seconds.

Leave and call the gas supplier first if you smell gas.

Leave the gas line, valves and igniters to the technician.

Arrange a diagnostic

Real scope. Clear expectations.

9US metro areas
11Appliance types
60Code explanations

The agreement comes first.

Before work starts

The technician describes the repair and agrees the cost with you before starting. We confirm the final figure once the oven, range or cooktop has been inspected.

Workmanship coverage

Dacor handles repairs that its manufacturer warranty covers. We provide a warranty of our own on the work we do.

Here to help

Good questions.
Clear answers.

Talk to our team
Why will one burner on my Dacor range not light?

The Heritage Pro table lists a cap not in place, a misaligned base, a dirty electrode or a knob not turned to Lite. Sort those out first; if the burner stays dark, a technician should take over.

What do I do if I smell gas?

Evacuate the building. Phone the gas supplier from a neighbor's home, as your own phone could cause a spark, and follow their directions.

Which Dacor ranges do you cover?

Heritage Pro HDPR30, 36 and 48, Heritage Induction HIPR30S and 36S, Transitional DOP30 and DOP36, and the Modernist DOP48 and DOP36 steam ranges.

Does a range code mean a bad oven?

Not always. The C-code tables describe sensors, door lock position and communication. The manuals ask for a restart first; the technician finds which part is behind it.

Does a warranty still cover my range?

While the manufacturer's warranty runs, that repair is the manufacturer's to handle. Once it ends, or if you prefer an independent technician, book a visit and the cost is settled with you first.

Let’s take care of it.

See a C-code?
Tell us the number.